>>> 'misc' problem from spivey -- Fri Jan  5 09:36:18 1990 <<<

The Herman Miller flipper drawer, in the reception area, over the gown 
boxes, has come off its runner.

>>> 'misc' problem from phillip -- Fri Jan  5 13:37:20 1990 <<<

Corrected HM flipper door fault as reported by Rosemary.

>>> 'misc' problem from bob -- Tue Jan  9 15:58:32 1990 <<<

A new hotplate has been installed in the old lab. This replaces
the missing one. The hotplate replaced is a Thermolyne.  A new 
one will be ordered for stock.

>>> 'misc' problem from saunders -- Wed Jan 10 16:43:42 1990 <<<

Lights in the chem room are not working.

>>> 'misc' problem from phillip -- Thu Jan 11 13:32:26 1990 <<<

P: (Explosion proof) lighting in the chem. storage rm.
   not working.
S:  Reterminated open conductor in lamp housing.
    Replaced bulbs. The problem as reported by
    Christine is fixed.

>>> 'misc' problem from marilyn -- Tue Jan 16 08:12:49 1990 <<<

Problem: Line printer is R1 is turned on, but not printing.

>>> 'misc' problem from bob -- Tue Jan 16 08:20:03 1990 <<<

The DEC PDP-11 computer has a defective DL-11 card. This prevented
the gcapg from booting. This card has failed in service several times
and will not be replaced. A new DEC VT-220 terminal has been orederd
which has a built in printer interface. It should be here within
30 days. This will allow us to run the printer and should speed up
the gcapg has it has a built in buffer. Until this terminal arrives
the printer is down.

>>> 'misc' problem from phillip -- Tue Jan 16 09:04:02 1990 <<<

The television set has been fastened to the video cart.
This should prevent it from falling off in transit.

>>> 'misc' problem from marilyn -- Wed Jan 17 13:24:59 1990 <<<

Problem: The telephone by the SEM does not ring; this makes call
that are transferred to line 3 difficult to pick up on.

>>> 'misc' problem from phillip -- Fri Jan 19 07:35:39 1990 <<<

The telephone by the SEM does ring. Moving the bell adjust lever
downward activates the bell. Moving the bell adjust lever upward
shuts the bell off. This explains the problem as reported by Marilyn.

>>> 'misc' problem from marilyn -- Mon Jan 29 10:22:41 1990 <<<

Problem: Vacuum wand handle at sink6 disintegrating/deteriorating
solution: Replaced with a new one

>>> 'misc' problem from bob -- Fri Feb  2 11:52:01 1990 <<<

The HV connectors on the Hi-potter have been replaced with 
real HV connectors. A new cable is on top of the machine. 
The Hi-potter is ready for use; however, it would be nice
to add new alligator clips.
These are on order.
Bob

>>> 'misc' problem from bob -- Mon Feb  5 09:13:38 1990 <<<

The canon copier is down again. It will be looked into by Evan
today.

>>> 'misc' problem from evan -- Mon Feb  5 11:22:56 1990 <<<

The canon copier START button has been repaired.
canon copier is up

>>> 'misc' problem from bob -- Mon Feb  5 11:26:35 1990 <<<

The canon copier in the office is fixed.

>>> 'misc' problem from bob -- Tue Feb  6 09:43:07 1990 <<<

The automatic documment feed on the canon sometimes skews the
paper. The problem appears to be on the large white feed belt 
that slides the documment on the glass plate. The problem will 
be reported to our vendor for service.
,
 

>>> 'misc' problem from phillip -- Wed Feb  7 11:19:09 1990 <<<

test

>>> 'misc' problem from pnelson -- Wed Feb  7 11:27:48 1990 <<<

An N2 gun has been installed near the orange hepa in the old lab.  It is
currently set at 30 psi.

>>> 'misc' problem from bob -- Fri Feb  9 15:44:16 1990 <<<

A new hotplate with stirrer has been placed in the old lab.
This replaces the missing unit.

>>> 'misc' problem from rnorman -- Tue Feb 27 07:25:18 1990 <<<

Two of the three LN2 tanks are empty and in need of filling.
Hebert is using the SST tank for the dw.

>>> 'misc' problem from marilyn -- Fri Mar  2 11:52:48 1990 <<<

Problem: RETURN key is missing at terminal in Y2.

>>> 'misc' problem from bill -- Sat Mar 10 14:24:39 1990 <<<

The card key reader is not operating.
I was unable to enter, another user tested his card
and he was not able to open the door either.
I'm pretty sure my card is fine - it got me in the building...

>>> 'misc' problem from kim -- Tue Mar 13 08:04:32 1990 <<<

Leaky vacuum wand next to Sink 6 and half of the magnets in the
VLSI room are not attracting the vacuum wands.

>>> 'misc' problem from bill -- Tue Mar 13 13:25:01 1990 <<<

Regarding the new set up in the analysis area :

Since the HP computer controls both the Ellips and the cv,
could it be moved in between the 2 pieces of equipment.

The current set up is rather awkward for cv users.
I'd be glad to meet with Phil and describe a setup
that might be more convenient for all users.

Thanks,
	Bill

>>> 'misc' problem from marilyn -- Wed Mar 14 08:19:33 1990 <<<

Problem: Bottom light of the Leitz microscope in R2 (PG room)
         is burned out.  This light is needed to examine completed
         masks.

>>> 'misc' problem from bob -- Wed Mar 14 14:08:30 1990 <<<

Problem : User reports lamp out on leitz microscope
Cause   : A rat!
Solution: Replaced missing bulb!!!

>>> 'misc' problem from judy -- Thu Mar 15 17:32:27 1990 <<<

The vibration isolation pods on the microscope in the vlsi area
seem to be turned off.  

>>> 'misc' problem from bob -- Fri Mar 16 13:53:37 1990 <<<

A user, for some unknown reason backed the regulators out on the
vibration table of the vlsi microscope. These have been returned
to normal, the steel table should be 1/8 inch raised from the deflated
position.

>>> 'misc' problem from kim -- Fri Mar 16 14:06:38 1990 <<<

Broken o-ring on the vacuum line of the silylation hotplate.

>>> 'misc' problem from bob -- Wed Mar 21 08:22:01 1990 <<<

The drinking fountain water is not being chilled. It will be looked into
when Phillip returns. The water quality is uneffected.

>>> 'misc' problem from phillip -- Fri Mar 23 07:22:58 1990 <<<

P: Drinking fountain water not being chilled.
S: Restored a.c. circuit breaker to 'on' position (B-4).
  The breaker was tripped by the ALaddin service man while
  repairing a chiller in the gas storage room.

The drinking fountain is up.

>>> 'misc' problem from evan -- Sun Mar 25 11:52:40 1990 <<<

There is water dripping from the fancoil unit in the tylan service chase.

>>> 'misc' problem from evan -- Mon Apr  2 08:10:26 1990 <<<

The intercom speaker is not working in the tylan service chase area.

>>> 'misc' problem from field -- Mon Apr  2 13:37:22 1990 <<<

Microscope in VLSI won't hold focus very well - once you focus
in, the knob starts spinning and the image becomes defocused.

>>> 'misc' problem from phillip -- Mon Apr  2 14:53:56 1990 <<<

P: Intercom speaker in tylanchase not working.
S: Reset open switch on intercom mixer box.
   The speaker is now operational.

>>> 'misc' problem from saunders -- Thu Apr  5 10:10:09 1990 <<<

The hook in VLSI for hanging aprons and faceshields on fell down.  It is sitting on the table.

>>> 'misc' problem from voros -- Thu Apr 12 08:06:45 1990 <<<

Lights above sink1 are out.

>>> 'misc' fix from phillip -- Mon Apr 16 08:15:41 1990 <<<

see hepa fix

>>> 'misc' problem from voros -- Mon Apr 23 09:12:36 1990 <<<

The placing of the shelf at the as200 needs to be designed ergonomically.
Pls see me.
Thanks.

>>> 'misc' problem from kuchta -- Fri Apr 27 10:51:58 1990 <<<

emergency flashlight in old lab by the nrc has burned out (bulb I guess)

>>> 'misc' fix from phillip -- Wed May  2 07:55:40 1990 <<<

Another 'emergency lamp' will be ordered to replace the one 
Dan Kuchta reported out by the NRC machine.

>>> 'misc' problem from richard -- Wed May  2 15:32:09 1990 <<<

The wires on the inline-switch on the power cord for the Lapmaster
monochromatic light (next to the MTI in Y2) have come loose and
shorted out.  (Fortunately I had my gloves on.)

>>> 'misc' fix from phillip -- Fri May  4 08:57:22 1990 <<<

Replaced a.c. cord switch on the 'lapmaster monochromatic
light source' in Y2. The problem reported by Richard is fixed.
The lightsource is available for use.

>>> 'misc' problem from kim -- Tue May  8 15:10:42 1990 <<<

Mettler Balance keep drifting.

>>> 'misc' fix from erc -- Mon Jul 16 16:11:42 1990 <<<

jingle bells, jingle bells, jingle all the way ...
oh what fun it is to ride in a one horse open sleigh!
