>>> 'misc' problem from vallath -- Tue Jan 10 17:11:04 1989 <<<

Lights above hepa 22 need replacing. 
Vallath

>>> 'misc' problem from jules -- Thu Jan 12 11:04:51 1989 <<<

Replaced both bulbs in HEPA #22.

Jules

>>> 'misc' problem from vallath -- Fri Jan 13 16:04:32 1989 <<<

sea-locker in Y1 sticks half-way down.

>>> 'misc' problem from galewski -- Fri Jan 13 18:29:59 1989 <<<

Why is there no vacuum wand by the nanospec?  Would be nice to 
have one connected so that in process wafers (cannot use metal
tweezer) need not be juggled with a teflon tweezer.

				Thank you,
				  Carl

>>> 'misc' problem from marilyn -- Tue Jan 17 10:36:03 1989 <<<

Problem: Ceiling light in R1 (above PG computer cabinet) flickering.

>>> 'misc' problem from phillip -- Tue Jan 17 14:34:30 1989 <<<

 Replaced lamps in redroom as reported by Marilyn.

>>> 'misc' problem from phillip -- Wed Jan 18 09:36:04 1989 <<<

Replaced (temp) 4'X4' VLSI ceiling tile that was overcome by
gravitational forces and shattered upon impact with the ground.
The correct color acrylic is being ordered by Mario for the
door and ceiling repair.(It is ~$140.00 per 4X8 sheet.)

>>> 'misc' problem from phillip -- Fri Jan 27 07:57:47 1989 <<<

The fan switch in the kitchen (rm.411) is broken and needs replacing.
As soon as a new one arrives, this feature will be fixed.

>>> 'misc' problem from phillip -- Tue Jan 31 10:50:51 1989 <<<

Replaced defective fan switch in kitchen with a new working switch.

>>> 'misc' problem from vallath -- Thu Feb  2 16:02:49 1989 <<<

The sea-locker in GL1 sticks, making it impossible to
reach the bottom shelf's contents.
VN

>>> 'misc' problem from richard -- Fri Feb 10 10:01:43 1989 <<<

The terminal in GL-4 often goes flaky.  Random characters appear
on the screen and the terminal often locks up, requiring a reset
from another terminal.  I reported this problem on the wand under
software problems but no action has been taken (it probably isn't
software since I don't see other terminals doing it).

>>> 'misc' problem from marilyn -- Tue Feb 14 10:55:56 1989 <<<

Fuse blown at Leitz microscope in the PG room.

>>> 'misc' problem from bob -- Tue Feb 14 12:08:51 1989 <<<

A new fuse has been installed and the leitz is up.

>>> 'misc' problem from vallath -- Tue Feb 21 18:11:52 1989 <<<

The manual for the scientech balance is outdated - also
the reading from it doesn't agree with the beam balances.
Vallath

>>> 'misc' problem from spivey -- Fri Mar  3 08:32:49 1989 <<<

Please replace overhead light in rm 421 over my desk.
Thank you.

>>> 'misc' problem from phillip -- Fri Mar  3 09:01:06 1989 <<<

 The lights that are out as reported by Rosemary are the result
of a defective ballast. We have none of this type. This will be
reported to DOFM by me via Cynthia today.

>>> 'misc' problem from jchung -- Sat Mar 11 11:50:49 1989 <<<

The microscope in the VLSI area has a leak in one of the
bellows supporting the scope.

>>> 'misc' problem from evan -- Mon Mar 13 14:53:15 1989 <<<

Found the leaky area of the bellows base.  I am sealing it up now.
The microscope can still be used but may have jitters due to lack
of vibration isolation. Do not try to inflate the base!

>>> 'misc' problem from voros -- Fri Mar 17 14:09:42 1989 <<<

The outside wall is peeling badly in Y2, seen through the HM wall. Pls remove panel and scrape off the peel as much
as possible.
Thanks.
Katalin

>>> 'misc' problem from evan -- Mon Mar 20 13:00:49 1989 <<<

problem: peeling pain
solution: removed panel and vacuumed up the loose paint.

>>> 'misc' problem from evan -- Tue Mar 21 16:53:08 1989 <<<

Problem: air leak in one of the vibration isolation feet.
Solution: tried to repair leak with various sealants but none available
were both flexible and strong enough to hold.  I therefore replaced the 
foot with a spare. 

>>> 'misc' problem from marilyn -- Wed Mar 22 09:02:26 1989 <<<

Problem: In R1, the APT room, the left-side C-locker door (behind
         sink12) is broken.

>>> 'misc' problem from vallath -- Wed Mar 22 11:33:51 1989 <<<

The 2.5 inch masks we get have flaws now and then, resulting in
wasted time spent in making them.
I had one just now which had quite  a few flaws, and one
of them was fatal, so $60 down the drain!
I was wondering if we can't get a better mask vendor, or are they
all like this.
Vallath

>>> 'misc' problem from liang -- Thu Mar 30 18:17:32 1989 <<<

The forming gas for small graphite heater used for 3-5 compound
device alloying is missing. Would you please install a new one
as soon as possible. The heater is in the old lab. Thanks.
chunlin

>>> 'misc' problem from liang -- Thu Mar 30 18:23:50 1989 <<<

I found the forming gas and it is connected to heater now. Everything
is ok. Please disregard the first message. Thanks
chunlin

>>> 'misc' problem from liang -- Thu Mar 30 18:25:38 1989 <<<

The forming gas has been connected to the heater. Please dis
regard the first message.
chunlun

>>> 'misc' problem from marilyn -- Mon Apr 17 14:40:10 1989 <<<

Problem: One of the wheels at my desk chair just *won't* stay on.

>>> 'misc' problem from marilyn -- Wed Apr 19 10:28:07 1989 <<<

Problem: Door handle to Y2 sticking; hard to open.

>>> 'misc' problem from evan -- Wed Apr 19 11:07:35 1989 <<<

problem: door handle sticking
solution: tightened screws on strike plate.  Tightened several others on
various other access doors.

>>> 'misc' problem from hsin -- Thu Apr 20 12:38:59 1989 <<<

The Mettler in the LPE room is again "beated" by somebody.
It can not be put on the 1/2 release. Somehow it is stucked
at the middle.  Service is needed. 

I would like to put it on torous so that no body can use it
without enable it.  It always happen that some one who don't
know how to operate it and jump onto it. It should be a very
high precision machine not to be abused by any one.

Wei Hsin

p.s. It can be put to full release, but this way can damage the
machine easily.

>>> 'misc' problem from kim -- Thu Apr 27 11:52:23 1989 <<<

Can't open the Y2 door easily.

>>> 'misc' problem from phillip -- Thu Apr 27 13:41:51 1989 <<<

Y2 door repaired temp.

>>> 'misc' problem from evan -- Thu Apr 27 17:15:45 1989 <<<

The lockset for Y2 door is broken.  The catch is detached from its position
lever (and is on my desk).  I'm try to repair tomorrow.  

>>> 'misc' problem from vallath -- Fri Apr 28 12:05:21 1989 <<<

The acetone spray gun in the old lab is not working right.
The nitrogen continues to blow irrespective of whetrher the
lever is pressed or not.
VN

>>> 'misc' problem from phillip -- Mon May  1 10:46:47 1989 <<<

P: Spray gun spewing n2 in 'off' mode.
S: Replaced springs and repaired settings
   on deVilbiss srray gun .These now work.

(Val, thanx for reporting this. An n2 leak like
this one could go on for a long time before being    
noticed by a staff person.)

>>> 'misc' problem from phillip -- Thu May  4 12:27:53 1989 <<<

Repaired Y2 door latch. Thank you for all the personal mail
bestowed upon me concerning this problem. 

>>> 'misc' problem from kim -- Fri May 12 09:21:41 1989 <<<

I wish someone can installed a N2 gun by the hummer or the
Mettler balance.

Kim

>>> 'misc' problem from evan -- Tue May 16 16:15:51 1989 <<<

Problem: 1/2 release broken
Cause: cam shaft turned too hard
Solution: The act of rotating the front knob clockwise to the half release
position causes a cam to raise a magnetic switch.  This switch turns on the
lamp.  The cam follower was not sliding smoothly up and down. I cleaned and
lubed the guides for this part.  The follower now moved freely but would 
still hang-up on the cam.  I discovered that the act of someone forcing the
knob and cam had put a dent in the plastic cam.  I was able to slide the
cam so the follower rode on an unmarked surface. The half release function
is now operational.
I would like to remind users that knobs, levers or switches should NEVER be
forced into any position they do not want to go.  In this case, it damaged
a critical piece which would be very time consuming to replace.  Please be
gentle with sensitive equipment such as balances and microscopes.

>>> 'misc' problem from bob -- Tue May 23 14:39:18 1989 <<<

Due to a volume of complaints, the charcoal filter was added back to the 
drinking fountain. The drinking fountain is up.

>>> 'misc' problem from qian -- Fri Jun  9 16:31:58 1989 <<<

Problem: Okidata printer does not print out files.

>>> 'misc' problem from phillip -- Mon Jun 12 07:47:42 1989 <<<

Reset lobby printer. The problem as reported by Qian is fixed.

>>> 'misc' problem from amar -- Mon Jun 12 15:11:31 1989 <<<

The tube connected to the nitrogen dry-gun in OLD LAB is cracked and
therefore leaking. Please replace or otherwise fix the tube.

>>> 'misc' problem from marilyn -- Wed Jun 14 13:12:17 1989 <<<

Problem: the left-hand C-locker door at sink12 in R1 is broken.
         (first reported several months ago)

>>> 'misc' problem from robin -- Wed Jun 28 11:01:19 1989 <<<

Vacuum wand next to technics-c is leaking.

>>> 'misc' problem from marilyn -- Wed Jun 28 14:04:07 1989 <<<

Problem: Vacuum wand next to technics-c leaking
Cause: Incompatible fittings
Solution: Replaced fittings; the wand leaks no more

>>> 'misc' problem from proclog -- Mon Jul 10 13:27:05 1989 <<<


Three lights out above Iona in Iona chase.

>>> 'misc' problem from phillip -- Tue Jul 11 11:08:56 1989 <<<

Replaced several expired bulbs in ionachase. Letr 
Let there be light!

>>> 'misc' problem from mario -- Thu Jul 13 13:34:00 1989 <<<

The door on the c-locker in GL-4 is broken.

>>> 'misc' problem from galewski -- Wed Jul 19 15:51:56 1989 <<<

I see a lot of oil depositing on surfaces out in nonenclosed breathable
air spaces.  To be specific I see alot of oil on Tylan door by the
outside filtration unit and by the tube 10 chiller.  Seems to me
that if enough oil to deposit on surface from air then we are breathing
it also.  I think it would be good to have such oil mist generators
such as the LAM pumps inside vented boxes.

My two cents for what its worth.

			-Carl

>>> 'misc' problem from marilyn -- Wed Aug  2 11:20:28 1989 <<<

Problem: The red lights above the MASKCOPY in R2 are burned out.

>>> 'misc' problem from phillip -- Wed Aug  2 14:57:02 1989 <<<

Lamps in R1 replaced per Marilyn's report.

>>> 'misc' problem from marilyn -- Wed Aug  2 15:41:09 1989 <<<

Problem: In R1, the APT room, the right-hand C-locker against
         the far wall across from sink12 has a broken door.

>>> 'misc' problem from partlo -- Mon Aug  7 15:54:45 1989 <<<

A light is out in the service chase for GL4.

>>> 'misc' problem from phillip -- Tue Aug  8 07:48:40 1989 <<<

Reseated loose bulb in midway chase.
The problem as reported by Partlo is fixed.

>>> 'misc' problem from evan -- Tue Aug 15 08:32:31 1989 <<<

A spare bulb for the Mettler Balance has been received and placed in
the spare bulb holder on the back of the balance. The replacement is
#11293-953 from VWR.

>>> 'misc' problem from bob -- Fri Aug 18 13:46:53 1989 <<<

The uv lamp source on the Leitz will not start due to internal arcing
in the power supply. It will be repaired shortly.

>>> 'misc' problem from phillip -- Mon Aug 21 07:02:14 1989 <<<

Replaced several flourescent lamps in the lobby area of
the newlab.

>>> 'misc' problem from rnorman -- Wed Aug 30 07:31:29 1989 <<<

Problem: Main N2 supply regulator in CG3 was leaking profussly.

Cause: The body on the regulator was cracked.

Solution: The regulator was replaced, tested and reset to the 
          correct pressure(40PSI).

>>> 'misc' problem from phillip -- Thu Aug 31 13:17:27 1989 <<<

Replaced several flourescent bulbs above ceiling level
in the VLSI area.

>>> 'misc' problem from hsin -- Wed Sep 13 12:18:35 1989 <<<

The temperature in the lab. becomes so high, I were always swetting!
The whole lab. just like in the furnace! 

Wei Hsin (09/13/89  12:15)

>>> 'misc' problem from kuchta -- Tue Sep 19 13:04:58 1989 <<<

The knob on the photoresist spinner in y1 has come off.  The spinner
is still functional though.
Dan

>>> 'misc' problem from marilyn -- Thu Sep 28 12:46:27 1989 <<<

Problem: The X-Y positioning knobs at the Olympus microscope
         in Y2 are loose; this makes examining wafers difficult.

>>> 'misc' problem from bob -- Fri Sep 29 16:01:35 1989 <<<

The microscope in Y-2 was examined and seems to work well. The x-y
motion controls have no adjustment for friction and to increase
it a thick grease will have to used on the rack. Robin and I will
go over it again on Monday and check its friction.

>>> 'misc' problem from bob -- Fri Sep 29 16:32:26 1989 <<<

The closure on the windows in Rm 421 is broken preventing the windows
from being properly closed. This mail will be cc'd to Eleta so PFM can
be contacted for repair.
Bob@argon
.

>>> 'misc' problem from tom -- Thu Oct  5 11:41:48 1989 <<<

The clock that was in VLSI is gone. Disappeared yesterday.

>>> 'misc' problem from rnorman -- Mon Oct 23 13:59:20 1989 <<<

I can't seem to find the Black Max N2 filters.  I looked in the gas
room were the other N2 filters are and in the GCA service chase; all
the N2 filters should be kept in the same spot.  If any one has information
as to there were abouts, please reply.

>>> 'misc' problem from phillip -- Tue Nov  7 08:40:33 1989 <<<

Replaced several flourescent bulbs in thed VLSI area.

>>> 'misc' problem from marilyn -- Thu Nov 16 11:13:15 1989 <<<

Problem: Ionized gun in PG room won't shut off- it keeps on
going.

>>> 'misc' problem from rnorman -- Fri Nov 17 08:04:45 1989 <<<

Problem: Ionized gun in PG room was leaking N2.

Cause: The hose was on the edge of blowing itself out of the
       fitting.

Solution: The hose was readjusted and the fitting tightened down.
          No leak occurred in the N2 gun.
From phillip Wed Dec  6 11:35:05 1989
Received: by argon (5.57/1.16)
	id AA04374; Wed, 6 Dec 89 11:34:54 PST
Date: Wed, 6 Dec 89 11:34:54 PST
From: phillip (Phill Guillory)
Message-Id: <8912061934.AA04374@argon>
To: /misc-p, lab_equip_probs, phillip
Subject: hepa problem
Status: R

Replaced no less than 36 flourescent tubes and 6 incandescent
lamps. 

Replaced no less than 6 hepa (#2F40) ballasts.

The oldlab and newlab are now brighter places.


>>> 'misc' problem from marilyn -- Thu Dec  7 15:31:00 1989 <<<

Problem: One of the Sunbeam clocks is broken; it was in Y2. It
is now on Evan's desk.

>>> 'misc' problem from voros -- Thu Dec 14 09:17:37 1989 <<<

Two lamps are flickering in the tylan chase.

>>> 'misc' problem from denlinge -- Thu Dec 14 22:03:54 1989 <<<

DI water is grinding to a halt.  There is none in sink8.  There is a 
trickle in Y1.  I noticed the pressure was lower than normal at about 7:00pm.
It has gotten much worse since then.

>>> 'misc' problem from phillip -- Tue Dec 19 09:12:09 1989 <<<

Replaced several lab hallway flourescent tubes.

>>> 'misc' problem from phillip -- Wed Dec 20 09:25:42 1989 <<<

It is now apparent that the original color coding scheme
for the ulility plumbiing is no longer adhered to.
Does this mean that ANY utility can be plumbed into ANY
color tubing? I do not recall seeing any mail granting
permission for doing this.

>>> 'misc' problem from marilyn -- Thu Dec 21 08:02:05 1989 <<<

Problem: Ionized gun at the gcapg was found on the tabletop in
         several pieces; somone must have dropped it on the floor
         last night.

>>> 'misc' problem from phillip -- Thu Dec 21 08:30:54 1989 <<<

Reassembled an ionized n2 gun that was , for whatever reason, apart.
The problem as reported by Marilyn is fixed.

>>> 'misc' problem from spivey -- Fri Jan  5 09:36:18 1990 <<<

The Herman Miller flipper drawer, in the reception area, over the gown 
boxes, has come off its runner.

>>> 'misc' problem from phillip -- Fri Jan  5 13:37:20 1990 <<<

Corrected HM flipper door fault as reported by Rosemary.

>>> 'misc' problem from bob -- Tue Jan  9 15:58:32 1990 <<<

A new hotplate has been installed in the old lab. This replaces
the missing one. The hotplate replaced is a Thermolyne.  A new 
one will be ordered for stock.

>>> 'misc' problem from saunders -- Wed Jan 10 16:43:42 1990 <<<

Lights in the chem room are not working.

>>> 'misc' problem from phillip -- Thu Jan 11 13:32:26 1990 <<<

P: (Explosion proof) lighting in the chem. storage rm.
   not working.
S:  Reterminated open conductor in lamp housing.
    Replaced bulbs. The problem as reported by
    Christine is fixed.

>>> 'misc' problem from marilyn -- Tue Jan 16 08:12:49 1990 <<<

Problem: Line printer is R1 is turned on, but not printing.

>>> 'misc' problem from bob -- Tue Jan 16 08:20:03 1990 <<<

The DEC PDP-11 computer has a defective DL-11 card. This prevented
the gcapg from booting. This card has failed in service several times
and will not be replaced. A new DEC VT-220 terminal has been orederd
which has a built in printer interface. It should be here within
30 days. This will allow us to run the printer and should speed up
the gcapg has it has a built in buffer. Until this terminal arrives
the printer is down.

>>> 'misc' problem from phillip -- Tue Jan 16 09:04:02 1990 <<<

The television set has been fastened to the video cart.
This should prevent it from falling off in transit.

>>> 'misc' problem from marilyn -- Wed Jan 17 13:24:59 1990 <<<

Problem: The telephone by the SEM does not ring; this makes call
that are transferred to line 3 difficult to pick up on.

>>> 'misc' problem from phillip -- Fri Jan 19 07:35:39 1990 <<<

The telephone by the SEM does ring. Moving the bell adjust lever
downward activates the bell. Moving the bell adjust lever upward
shuts the bell off. This explains the problem as reported by Marilyn.

>>> 'misc' problem from marilyn -- Mon Jan 29 10:22:41 1990 <<<

Problem: Vacuum wand handle at sink6 disintegrating/deteriorating
solution: Replaced with a new one

>>> 'misc' problem from bob -- Fri Feb  2 11:52:01 1990 <<<

The HV connectors on the Hi-potter have been replaced with 
real HV connectors. A new cable is on top of the machine. 
The Hi-potter is ready for use; however, it would be nice
to add new alligator clips.
These are on order.
Bob

>>> 'misc' problem from bob -- Mon Feb  5 09:13:38 1990 <<<

The canon copier is down again. It will be looked into by Evan
today.

>>> 'misc' problem from evan -- Mon Feb  5 11:22:56 1990 <<<

The canon copier START button has been repaired.
canon copier is up

>>> 'misc' problem from bob -- Mon Feb  5 11:26:35 1990 <<<

The canon copier in the office is fixed.

>>> 'misc' problem from bob -- Tue Feb  6 09:43:07 1990 <<<

The automatic documment feed on the canon sometimes skews the
paper. The problem appears to be on the large white feed belt 
that slides the documment on the glass plate. The problem will 
be reported to our vendor for service.
,
 

>>> 'misc' problem from phillip -- Wed Feb  7 11:19:09 1990 <<<

test

>>> 'misc' problem from pnelson -- Wed Feb  7 11:27:48 1990 <<<

An N2 gun has been installed near the orange hepa in the old lab.  It is
currently set at 30 psi.

>>> 'misc' problem from bob -- Fri Feb  9 15:44:16 1990 <<<

A new hotplate with stirrer has been placed in the old lab.
This replaces the missing unit.

>>> 'misc' problem from rnorman -- Tue Feb 27 07:25:18 1990 <<<

Two of the three LN2 tanks are empty and in need of filling.
Hebert is using the SST tank for the dw.

>>> 'misc' problem from marilyn -- Fri Mar  2 11:52:48 1990 <<<

Problem: RETURN key is missing at terminal in Y2.

>>> 'misc' problem from bill -- Sat Mar 10 14:24:39 1990 <<<

The card key reader is not operating.
I was unable to enter, another user tested his card
and he was not able to open the door either.
I'm pretty sure my card is fine - it got me in the building...

>>> 'misc' problem from kim -- Tue Mar 13 08:04:32 1990 <<<

Leaky vacuum wand next to Sink 6 and half of the magnets in the
VLSI room are not attracting the vacuum wands.

>>> 'misc' problem from bill -- Tue Mar 13 13:25:01 1990 <<<

Regarding the new set up in the analysis area :

Since the HP computer controls both the Ellips and the cv,
could it be moved in between the 2 pieces of equipment.

The current set up is rather awkward for cv users.
I'd be glad to meet with Phil and describe a setup
that might be more convenient for all users.

Thanks,
	Bill

>>> 'misc' problem from marilyn -- Wed Mar 14 08:19:33 1990 <<<

Problem: Bottom light of the Leitz microscope in R2 (PG room)
         is burned out.  This light is needed to examine completed
         masks.

>>> 'misc' problem from bob -- Wed Mar 14 14:08:30 1990 <<<

Problem : User reports lamp out on leitz microscope
Cause   : A rat!
Solution: Replaced missing bulb!!!

>>> 'misc' problem from judy -- Thu Mar 15 17:32:27 1990 <<<

The vibration isolation pods on the microscope in the vlsi area
seem to be turned off.  

>>> 'misc' problem from bob -- Fri Mar 16 13:53:37 1990 <<<

A user, for some unknown reason backed the regulators out on the
vibration table of the vlsi microscope. These have been returned
to normal, the steel table should be 1/8 inch raised from the deflated
position.

>>> 'misc' problem from kim -- Fri Mar 16 14:06:38 1990 <<<

Broken o-ring on the vacuum line of the silylation hotplate.

>>> 'misc' problem from bob -- Wed Mar 21 08:22:01 1990 <<<

The drinking fountain water is not being chilled. It will be looked into
when Phillip returns. The water quality is uneffected.

>>> 'misc' problem from phillip -- Fri Mar 23 07:22:58 1990 <<<

P: Drinking fountain water not being chilled.
S: Restored a.c. circuit breaker to 'on' position (B-4).
  The breaker was tripped by the ALaddin service man while
  repairing a chiller in the gas storage room.

The drinking fountain is up.

>>> 'misc' problem from evan -- Sun Mar 25 11:52:40 1990 <<<

There is water dripping from the fancoil unit in the tylan service chase.

>>> 'misc' problem from evan -- Mon Apr  2 08:10:26 1990 <<<

The intercom speaker is not working in the tylan service chase area.

>>> 'misc' problem from field -- Mon Apr  2 13:37:22 1990 <<<

Microscope in VLSI won't hold focus very well - once you focus
in, the knob starts spinning and the image becomes defocused.

>>> 'misc' problem from phillip -- Mon Apr  2 14:53:56 1990 <<<

P: Intercom speaker in tylanchase not working.
S: Reset open switch on intercom mixer box.
   The speaker is now operational.

>>> 'misc' problem from saunders -- Thu Apr  5 10:10:09 1990 <<<

The hook in VLSI for hanging aprons and faceshields on fell down.  It is sitting on the table.

>>> 'misc' problem from voros -- Thu Apr 12 08:06:45 1990 <<<

Lights above sink1 are out.

>>> 'misc' fix from phillip -- Mon Apr 16 08:15:41 1990 <<<

see hepa fix

>>> 'misc' problem from voros -- Mon Apr 23 09:12:36 1990 <<<

The placing of the shelf at the as200 needs to be designed ergonomically.
Pls see me.
Thanks.

>>> 'misc' problem from kuchta -- Fri Apr 27 10:51:58 1990 <<<

emergency flashlight in old lab by the nrc has burned out (bulb I guess)

>>> 'misc' fix from phillip -- Wed May  2 07:55:40 1990 <<<

Another 'emergency lamp' will be ordered to replace the one 
Dan Kuchta reported out by the NRC machine.

>>> 'misc' problem from richard -- Wed May  2 15:32:09 1990 <<<

The wires on the inline-switch on the power cord for the Lapmaster
monochromatic light (next to the MTI in Y2) have come loose and
shorted out.  (Fortunately I had my gloves on.)

>>> 'misc' fix from phillip -- Fri May  4 08:57:22 1990 <<<

Replaced a.c. cord switch on the 'lapmaster monochromatic
light source' in Y2. The problem reported by Richard is fixed.
The lightsource is available for use.

>>> 'misc' problem from kim -- Tue May  8 15:10:42 1990 <<<

Mettler Balance keep drifting.

>>> 'misc' fix from erc -- Mon Jul 16 16:11:42 1990 <<<

jingle bells, jingle bells, jingle all the way ...
oh what fun it is to ride in a one horse open sleigh!
