>>> 'aptemul' problem from straub -- Mon Feb 20 11:26:04 1989 <<<

possible problem- see problem for gcapg

>>> 'aptemul' problem from marilyn -- Tue Feb 21 08:53:08 1989 <<<

Problem: user reported that a 4X development was necessary to develop
         emulsion masks
Cause: user had exposed his emulsion masks with CHROME parameters
Solution: as a precaution, made new developer with a freshly opened
          bottle/the aptemul developer is fine

>>> 'aptemul' problem from kim -- Fri Mar  3 16:07:33 1989 <<<

Problem:  Loosen screw for the viewing window and dirty window.
          Tighten screw, but the Scott Brite is missing for
          cleaning the window.  It is hard to see the spray
          pattern on the test run now.

>>> 'aptemul' problem from bob -- Mon Mar  6 08:48:02 1989 <<<

In the words of Phil,
Reimbued original lustre to aptemul window using plastic polish.

>>> 'aptemul' problem from kim -- Tue Apr 25 08:52:25 1989 <<<

The spray nozzle on the fixer line comes out in a thin stream
which it should be a strong fan like spray.  Please check the
pump.

Kim

>>> 'aptemul' problem from bob -- Fri Apr 28 14:19:02 1989 <<<

The aptemul has a bad pump. A spare has been put on line and the aptemul
is operational. Phil will look into the bad pump on Monday.
From marilyn Fri Apr 28 13:44:56 1989
Received: by argon (5.57/1.16)
	id AA17786; Fri, 28 Apr 89 13:44:46 PDT
Date: Fri, 28 Apr 89 13:44:46 PDT
From: marilyn (Marilyn Kushner)
Message-Id: <8904282044.AA17786@argon>
To: aptemul
Subject: Rapid Fixer Line Switched
Status: R


Until further notice, use the RED line for rapid fixer; the
pump to the orange line is not working.  Programs 82 and 2
haved been edited to reflect this change.

Kim/Marilyn


>>> 'aptemul' problem from phillip -- Mon May  1 09:00:17 1989 <<<

P: Output 0 (orange line) not functioning.
S: Cleared pump line of hardened solution.
   The orange line works normally again.
   The aptE  is up.

>>> 'aptemul' problem from denlinge -- Thu Aug 17 00:19:55 1989 <<<

The light is not working, I don't think my masks will develope without it.

>>> 'aptemul' problem from phillip -- Thu Aug 17 09:15:48 1989 <<<

P:No lamp. No motor.
S: Reconnected loose solder lead @ 2nd diode rectifier junction
   of power supply.	
   This machine is up and available for use.

>>> 'aptemul' problem from hphlee -- Sat Aug 26 15:30:53 1989 <<<

did not use it. Developer and Fixer both running low.
Henry

>>> 'aptemul' problem from marilyn -- Mon Aug 28 08:23:15 1989 <<<

Problem: A qualified user reported that the developer and rapid fixer
         levels were low, and he could therefore not use the aptemul.
Solution: New solutions were made up; bottles are refilled.
          Memo: ALL qualified users know how to do this, and should as
          as a courtesy to the next user.  This person has been sent
          e-mail to see me for a refresher lesson.

>>> 'aptemul' problem from marilyn -- Tue Nov 28 09:36:47 1989 <<<

Problem: Red shield/door to aptemul needs to be replaced; it's
         scratched beyond repair.

>>> 'aptemul' problem from phillip -- Thu Nov 30 07:57:57 1989 <<<

The red door cost is more than $200.00 . 
Marilyn, I have some plastic polish that should
clear up the lens. I will provide you with it.
This fix is o.k. per Robin/Debra

>>> 'aptemul' problem from bob -- Fri Jan 12 08:25:46 1990 <<<

I used a little polish on the door for about 5 minutes and the
door looks much better. I can show Marilyn were the polish is
and with more work I believe we can get the door back to it's
full transparency. This procedure will have to be a regular
pm in order to maintain the red windows clarity.

>>> 'aptemul' problem from bob -- Wed Feb 28 15:55:30 1990 <<<

The aptemul has been put out of service for the evening as
sink10 is none functional (drain for apt's) due to a power 
problem.

>>> 'aptemul' problem from phillip -- Fri Mar  2 08:32:02 1990 <<<

The emulsion machine should be o.k. now.

>>> 'aptemul' problem from phillip -- Fri Mar  9 14:24:58 1990 <<<

Replaced backup memory battery on circuit board. 
The emulsion machine is up.

>>> 'aptemul' problem from marilyn -- Fri Mar  9 15:25:47 1990 <<<

Problem: Test and development programs wiped out after Phill replaced
         the battery memory backup.
Solution: Reprogrammed back in.

>>> 'aptemul' problem from marilyn -- Mon Mar 12 11:46:42 1990 <<<

Problem: Programs for testing the lines and developing were wiped
         out when aptemul power was turned on.
Solution: reprogrammed Programs 82 (test lines) and 2 (develop)
          back in
          The aptemul is up.

>>> 'aptemul' problem from marilyn -- Wed Mar 14 08:17:14 1990 <<<

Problem: APTemul programs wiped put.
         *Note: All programs are randomly erased whether or not
          the power switch is turned on.
Cause: Undetermined to date.
Solution: Reprogrammed Programs 82/2/92.

>>> 'aptemul' problem from marilyn -- Thu Mar 15 08:03:24 1990 <<<

Problem: Test/develop/clear lines programs wiped out after APTemul
         power was turned off for the night, then turned back on in 
         the morning.
Solution: Reprogrammed back in (Programs 82,2, 92.)

>>> 'aptemul' problem from bob -- Fri Mar 16 10:55:26 1990 <<<

The aptemul is haviing trouble with storing recipes. New RAM has been
ordered which should solve this problem. Until then, recipes may have
to be periodically re-entered.

>>> 'aptemul' problem from phillip -- Fri Mar 23 09:28:15 1990 <<<

P: Emulsion machine will not hold memory.
S: Replaced defected memory chips. Replaced 3v 
   lithium battery.

 The memory storage problem as we have had is repaired.

This machine is up and available for use.

RPO: 2 memory chips in PCB position # U-26 & U-27
     chip # HM3-6514-9

>>> 'aptemul' problem from phillip -- Tue Mar 27 07:42:57 1990 <<<

The emulsion machine will be DOWN until 10:00a.m. for service.

>>> 'aptemul' problem from phillip -- Tue Mar 27 09:01:06 1990 <<<

The emulsion machine is now available for use.

>>> 'aptemul' problem from marilyn -- Tue Mar 27 10:27:22 1990 <<<

Problem: Memory went out again. (Program 82- which was programmed
in this morning- disappeared.) All the output (red lights) are on.

>>> 'aptemul' problem from marilyn -- Thu Mar 29 09:15:01 1990 <<<

Problem: Solenoid creating a terrific rattling during mask develop

>>> 'aptemul' fix from phillip -- Tue Apr 10 14:32:32 1990 <<<

P: Emulsion machine loses memory.
S: Ordered and installed new ic memory.
   This machine has been tested by Marilyn 
   and is up and working.
