patch-2.4.0-test11 linux/include/linux/ethtool.h

• Lines: 98
• Date: Sun Nov 12 20:37:17 2000
• Orig file: v2.4.0-test10/linux/include/linux/ethtool.h
• Orig date: Wed Dec 31 16:00:00 1969

diff -u --recursive --new-file v2.4.0-test10/linux/include/linux/ethtool.h linux/include/linux/ethtool.h
@@ -0,0 +1,97 @@
+/* $Id: ethtool.h,v 1.2 2000/11/12 10:05:57 davem Exp $
+ * ethtool.h: Defines for Linux ethtool.
+ *
+ * Copyright (C) 1998 David S. Miller (davem@redhat.com)
+ */
+
+#ifndef _LINUX_ETHTOOL_H
+#define _LINUX_ETHTOOL_H
+
+
+/* This should work for both 32 and 64 bit userland. */
+struct ethtool_cmd {
+	u32	cmd;
+	u32	supported;	/* Features this interface supports */
+	u32	advertising;	/* Features this interface advertises */
+	u16	speed;		/* The forced speed, 10Mb, 100Mb, gigabit */
+	u8	duplex;		/* Duplex, half or full */
+	u8	port;		/* Which connector port */
+	u8	phy_address;
+	u8	transceiver;	/* Which tranceiver to use */
+	u8	autoneg;	/* Enable or disable autonegotiation */
+	u32	maxtxpkt;	/* Tx pkts before generating tx int */
+	u32	maxrxpkt;	/* Rx pkts before generating rx int */
+	u32	reserved[4];
+};
+
+
+/* CMDs currently supported */
+#define ETHTOOL_GSET		0x00000001 /* Get settings, non-privileged. */
+#define ETHTOOL_SSET		0x00000002 /* Set settings, privileged. */
+
+/* compatibility with older code */
+#define SPARC_ETH_GSET		ETHTOOL_GSET
+#define SPARC_ETH_SSET		ETHTOOL_SSET
+
+/* Indicates what features are supported by the interface. */
+#define SUPPORTED_10baseT_Half		(1 << 0)
+#define SUPPORTED_10baseT_Full		(1 << 1)
+#define SUPPORTED_100baseT_Half		(1 << 2)
+#define SUPPORTED_100baseT_Full		(1 << 3)
+#define SUPPORTED_1000baseT_Half	(1 << 4)
+#define SUPPORTED_1000baseT_Full	(1 << 5)
+#define SUPPORTED_Autoneg		(1 << 6)
+#define SUPPORTED_TP			(1 << 7)
+#define SUPPORTED_AUI			(1 << 8)
+#define SUPPORTED_MII			(1 << 9)
+#define SUPPORTED_FIBRE			(1 << 10)
+
+/* Indicates what features are advertised by the interface. */
+#define ADVERTISED_10baseT_Half		(1 << 0)
+#define ADVERTISED_10baseT_Full		(1 << 1)
+#define ADVERTISED_100baseT_Half	(1 << 2)
+#define ADVERTISED_100baseT_Full	(1 << 3)
+#define ADVERTISED_1000baseT_Half	(1 << 4)
+#define ADVERTISED_1000baseT_Full	(1 << 5)
+#define ADVERTISED_Autoneg		(1 << 6)
+#define ADVERTISED_TP			(1 << 7)
+#define ADVERTISED_AUI			(1 << 8)
+#define ADVERTISED_MII			(1 << 9)
+#define ADVERTISED_FIBRE		(1 << 10)
+
+/* The following are all involved in forcing a particular link
+ * mode for the device for setting things.  When getting the
+ * devices settings, these indicate the current mode and whether
+ * it was foced up into this mode or autonegotiated.
+ */
+
+/* The forced speed, 10Mb, 100Mb, gigabit. */
+#define SPEED_10		10
+#define SPEED_100		100
+#define SPEED_1000		1000
+
+/* Duplex, half or full. */
+#define DUPLEX_HALF		0x00
+#define DUPLEX_FULL		0x01
+
+/* Which connector port. */
+#define PORT_TP			0x00
+#define PORT_AUI		0x01
+#define PORT_MII		0x02
+#define PORT_FIBRE		0x03
+#define PORT_BNC		0x04
+
+/* Which tranceiver to use. */
+#define XCVR_INTERNAL		0x00
+#define XCVR_EXTERNAL		0x01
+#define XCVR_DUMMY1		0x02
+#define XCVR_DUMMY2		0x03
+#define XCVR_DUMMY3		0x04
+
+/* Enable or disable autonegotiation.  If this is set to enable,
+ * the forced link modes above are completely ignored.
+ */
+#define AUTONEG_DISABLE		0x00
+#define AUTONEG_ENABLE		0x01
+
+#endif /* _LINUX_ETHTOOL_H */